Sunday, 30 November 2014

SFX Practical Creating Sculpt and Moulds

Preparation of the Mould & Sculpting

For this step of mould making you will need

Non-porous surface
Sculpting tools
Gloves
Sulphur free moulding clay




1.     Find a non-porous surface to sculpt on e.g. a smooth piece of plastic

2.     Put on gloves to prevent contamination of the clay, some things can stop silicone working properly.

3.     Apply your amount of clay onto the center of the plastic and start moulding your shape. You can add or take away clay.

4.     Blend the edges of the clay away smoothly so that it will allow your mould to blend into the skin when applied. EVERYTHING THAT IS ON YOUR MOULD WILL SHOW UP, so take your time perfecting it.

5.     Avoid creating overhanging edges as it will make it difficult or impossible to remove your negative from the mould.


Creating the negative of your mould

For this step of the mould making, you will need:

Silicone part A
Silicone part B
Measuring Cups
Digital Scales
Glue Gun
Fixer Spray
Petrolease
Gloves
Spatulas


HEALTH AND SAFTEY

·       When using silicone, make sure all surfaces are covered to prevent spillage and staining.
·       When using a glue gun, keep your fingers away from the metal nib and fresh glue as it becomes very hot.
·       When using sprays make sure you are working in a ventilated area.
·       Do not contaminate Silicone part A with B, as any single drop will solidify it.



1.     Spray sculpt with fixer spray, let dry.

2.     Spray sculpt with petrolease spray, let dry

3.     Cut the bottom of your measuring cup off and with a hot glue gun, stick down around the sculpt. This is to make a barrier around your sculpt to allow you to pour your silicone over the sculpt.

4.     Mix 1 -1 of silicone part A and B, use a digital scale to accurately measure equal amounts of both parts. Mix well with a spatula.

5.     Pour the mixture over the sculpt

6.     Leave to dry.


Removing the mould from the sculpt

For this part of the mould making, you will need:

Gloves
Spatula
IPA Brush Cleaner
Baldiez
Release Spray
Acetone
Hairdryer
Measuring Cups
Electronis Scales
Brush
Powder

1.     When your silicone for the mould has entirely dried and solidified, remove the mould from the sculpt. You will may need to cut open the measuring cup.

2.     Clean the mould using baby buds and IPA brush cleanser

3.     Spray all over the mould with release spray

4.     Mix 1 baldiez with 2 acetone

5.     Swill the mixture around the mould and use a brush to make sure every part of the mould is evenly covered.

6.     Put on a level surface and allow to dry, you will know it is dry when the mixture goes matte. Make sure there are no holes, if there are you can cover with another layer, you can do up to six layers.

7.     Mix same amount of silicone 50/50=100 + 90% of C (Deadener), for a larger piece mix 75/75 +135 grams + C deadener. Add 90% of final mix for smaller pieces 40% for longer and bigger pieces. Mix together A, B and C well.

8.     Mix a tiny drop of colour into the mixture.

9.     Pour into the mould, wipe off any excess with a ruler and smooth the edges with a baby bud.

10.  Leave to dry, it should take 12 – 20 minutes, thicker moulds will take longer. It is dry when it doesn’t leave a fingerprint when you touch it.

11.  When dry, powder the mould to get rid of the tacky surface


Application of the piece to the face

For the application step, you will need,

Prosaide (contact glue)
Piece of card
Baby Buds
Bushes
Acetone
Alcohol activated palette
Foundation/concealer palette
Prosaide remover


HEALTH AND SAFETY

·       When applying the piece close to the eyes, always tell your model to close their eyes.
·       If model has very sensitive skin, use a barrier cream before applying the piece.
·       Always remove prosaide glue with prosaide remover.


1.     Get a square piece of card, cut a circle out that is larger than the actual size of your piece.

2.     Glue your piece to the card with prosaide.

3.     Apply prosaide to the area of the face you want to apply the piece. Apply a even amount of prosaide to the back of the piece.

4.     Carefully apply the piece and using a baby bub smooth down the whole surface.

5.     Using acetone, remove the excess and dissolve and blend away the edges.

6.     Once all edges are blended, colour the piece with foundation, you want to match it as close as possible with the model’s natural skin tone. DO NOT RUB PROSTETIC PIECES, ALWAYS DAB.


7.     Look at the model’s skin tone, determine whether he/she is olive toned, neutral or pink toned. Using the alcohol activated palette select the colours that are needed to match the models face and flick onto the piece, again make sure the model has their eyes closed. This will give the most realistic skin texture.





As you can see, I didn't do that great a job with blending on my first attempt. I didn't apply enough glue to the prosthetic piece and that allowed the edges to curl upwards when I tried to blend with the acetone. Another problem was that the prosthetic piece that I made was too soft and when I tried to blend in the edges, it would pull and stretch the piece making it less easy to work with.  

No comments:

Post a Comment