Preparation
of the Mould & Sculpting
For
this step of mould making you will need
Non-porous
surface
Sculpting
tools
Gloves
Sulphur
free moulding clay
1.
Find a non-porous surface to sculpt on e.g. a smooth
piece of plastic
2.
Put on gloves to prevent contamination of the clay,
some things can stop silicone working properly.
3.
Apply your amount of clay onto the center of the
plastic and start moulding your shape. You can add or take away clay.
4.
Blend the edges of the clay away smoothly so that it
will allow your mould to blend into the skin when applied. EVERYTHING THAT IS
ON YOUR MOULD WILL SHOW UP, so take your time perfecting it.
5.
Avoid creating overhanging edges as it will make it
difficult or impossible to remove your negative from the mould.
Creating
the negative of your mould
For
this step of the mould making, you will need:
Silicone
part A
Silicone
part B
Measuring
Cups
Digital
Scales
Glue
Gun
Fixer
Spray
Petrolease
Gloves
Spatulas
HEALTH
AND SAFTEY
· When using
silicone, make sure all surfaces are covered to prevent spillage and staining.
· When using a glue
gun, keep your fingers away from the metal nib and fresh glue as it becomes
very hot.
· When using sprays
make sure you are working in a ventilated area.
· Do not
contaminate Silicone part A with B, as any single drop will solidify it.
1. Spray sculpt with
fixer spray, let dry.
2. Spray sculpt with
petrolease spray, let dry
3. Cut the bottom of
your measuring cup off and with a hot glue gun, stick down around the sculpt.
This is to make a barrier around your sculpt to allow you to pour your silicone
over the sculpt.
4. Mix 1 -1 of
silicone part A and B, use a digital scale to accurately measure equal amounts
of both parts. Mix well with a spatula.
5. Pour the mixture
over the sculpt
6. Leave to dry.
Removing
the mould from the sculpt
For
this part of the mould making, you will need:
Gloves
Spatula
IPA
Brush Cleaner
Baldiez
Release
Spray
Acetone
Hairdryer
Measuring
Cups
Electronis
Scales
Brush
Powder
1. When your
silicone for the mould has entirely dried and solidified, remove the mould from
the sculpt. You will may need to cut open the measuring cup.
2. Clean the mould
using baby buds and IPA brush cleanser
3. Spray all over
the mould with release spray
4. Mix 1 baldiez
with 2 acetone
5. Swill the mixture
around the mould and use a brush to make sure every part of the mould is evenly
covered.
6. Put on a level
surface and allow to dry, you will know it is dry when the mixture goes matte.
Make sure there are no holes, if there are you can cover with another layer,
you can do up to six layers.
7. Mix same amount
of silicone 50/50=100 + 90% of C (Deadener), for a larger piece mix 75/75 +135
grams + C deadener. Add 90% of final mix for smaller pieces 40% for longer and
bigger pieces. Mix together A, B and C well.
8. Mix a tiny drop
of colour into the mixture.
9. Pour into the
mould, wipe off any excess with a ruler and smooth the edges with a baby bud.
10. Leave to dry, it
should take 12 – 20 minutes, thicker moulds will take longer. It is dry when it
doesn’t leave a fingerprint when you touch it.
11. When dry, powder
the mould to get rid of the tacky surface
Application
of the piece to the face
For
the application step, you will need,
Prosaide
(contact glue)
Piece
of card
Baby
Buds
Bushes
Acetone
Alcohol
activated palette
Foundation/concealer
palette
Prosaide
remover
HEALTH
AND SAFETY
· When applying the
piece close to the eyes, always tell your model to close their eyes.
· If model has very
sensitive skin, use a barrier cream before applying the piece.
· Always remove
prosaide glue with prosaide remover.
1. Get a square
piece of card, cut a circle out that is larger than the actual size of your
piece.
2. Glue your piece
to the card with prosaide.
3. Apply prosaide to
the area of the face you want to apply the piece. Apply a even amount of
prosaide to the back of the piece.
4. Carefully apply
the piece and using a baby bub smooth down the whole surface.
5. Using acetone,
remove the excess and dissolve and blend away the edges.
6. Once all edges
are blended, colour the piece with foundation, you want to match it as close as
possible with the model’s natural skin tone. DO NOT RUB PROSTETIC PIECES,
ALWAYS DAB.
7. Look at the
model’s skin tone, determine whether he/she is olive toned, neutral or pink
toned. Using the alcohol activated palette select the colours that are needed
to match the models face and flick onto the piece, again make sure the model
has their eyes closed. This will give the most realistic skin texture.









